This page presents the ASTM F594 Group 4 material specification as manufactured to at Ananka Fasteners Pvt Ltd. F594 Group 4 covers stainless steel nuts in martensitic and precipitation-hardening grades 410, 416, 420, 431, 15-5 PH, 17-4 PH. The chemistry and mechanical properties below are the values delivered to on every fastener released against this specification.
F594 Group 4 covers stainless steel nuts in martensitic and precipitation-hardening grades 410, 416, 420, 431, 15-5 PH, 17-4 PH.
| Specification | ASTM F594 Group 4 | Governs | Chemistry and mechanicals for one or more grades of fastener material |
| Grades Covered | SS 15-5 PH, SS 420, SS 431 | Product Forms | Bolts / Screws / Studs / Nuts / Washers as manufactured to the geometry standard |
| Related Dimensional Standards | ASME B18.2.1, DIN 931/933, ISO 4014, BS 3692 | Datasheets Referencing this Spec | 16 |
| Certification | EN 10204 3.1 / 3.2 | Testing | PMI, chemistry, tensile, hardness, IGC where applicable |
The following material grades are supplied by Ananka to ASTM F594 Group 4:
Composition limits shown are representative for the primary grade governed by this specification. Consult the individual grade datasheet for exact limits.
| Element | Composition, % |
|---|---|
| Chromium | 12.0–14.0 |
| Carbon, min | 0.15 |
| Manganese, max | 1.0 |
| Silicon, max | 1.0 |
| Phosphorus, max | 0.040 |
| Sulfur, max | 0.030 |
| Iron | Balance |
Minimum mechanical properties governing fasteners released to this specification:
| Condition / Temper | Tensile Strength min, psi (MPa) | Yield Strength min, psi (MPa) | Elongation min, % | Hardness |
|---|---|---|---|---|
| Hardened & tempered bar | 120 000 (825) | 90 000 (620) | 12 | ≤50 HRC |
All standard fastener geometries manufactured at Ananka can be released to ASTM F594 Group 4:
Every batch released to ASTM F594 Group 4 is verified by internal and third-party testing.
For technical documentation and quotations, buyers can also review the Ananka Fasteners manufacturing and supply range or contact the team through the fastener enquiry and technical support page.
This datasheet references ASTM F594 Group 4 for material and fastener requirements. Related dimensional standards commonly paired with this specification include ASME B18.2.1, DIN 931/933, ISO 4014, BS 3692. The applicable standard edition and purchase requirements should be confirmed for every project.
For ASTM International material and fastener specifications, see the ASTM International standards catalogue. This external reference is provided for standards identification; the purchaser should verify the current edition applicable to the order.
ASTM F594 Group 4 chemistry and mechanicals for one or more grades of fastener material. It covers SS 15-5 PH, SS 420, SS 431.
Ananka Fasteners supplies SS 15-5 PH, SS 420, SS 431 to this specification. See Section 2 above for the complete list.
Bolts / Screws / Studs / Nuts / Washers as manufactured to the geometry standard can be released to ASTM F594 Group 4, manufactured to the corresponding geometry standard.
ASTM F594 Group 4 fasteners are commonly manufactured to ASME B18.2.1, DIN 931/933, ISO 4014, BS 3692, depending on the fastener type required.
Yes. For a quotation, provide the required fastener type, material grade, nominal size, dimensional standard, quantity and any inspection or certificate requirements.
Need a fastener released to ASTM F594 Group 4 for an industrial project? Send the required fastener type, material grade, size, quantity and certification requirements to Ananka Fasteners. Our team can review the requirement and provide technical and commercial information for standard or custom configurations.
Recommended RFQ details: ASTM F594 Group 4 requirement, material grade, fastener type, nominal size, quantity, inspection requirements and EN 10204 certificate requirements where applicable.
