At Ananka Fasteners Pvt Ltd, we manufacture and supply fasteners certified to ASTM F2482/F2482M. CORRECTION: ASTM F2482 is ‘Load-Indicating Externally Threaded Fasteners’ – bolts, studs and cap screws with integral sensing that indicate clamp force during tightening or residual tension in service (not a generic bolt material spec). Sizes 1/4 to 7 in [M6-M180].
CORRECTION: ASTM F2482 is ‘Load-Indicating Externally Threaded Fasteners’ – bolts, studs and cap screws with integral sensing that indicate clamp force during tightening or residual tension in service (not a generic bolt material spec). Sizes 1/4 to 7 in [M6-M180].
| Grade / Class | UNS / Designation | Type / Notes |
|---|---|---|
| Mechanical Dial Type (MT) | n/a | Mechanical indicator shows tension |
| Electronic Type (ET) | n/a | Embedded electronic sensor |
| Strain Gauge Type (ST) | n/a | Strain-gauge instrumented |
| Ultrasonic Type (UT) | n/a | Ultrasonic elongation measurement |
Minimum mechanical requirements per ASTM F2482/F2482M.
| Grade / Class / Condition | Tensile Strength, min | Yield Strength, min | Elongation, min % | Hardness |
|---|---|---|---|---|
| Per governing base-fastener spec | per base spec | per base spec | per base spec | per base spec |
| Load-indication accuracy | indicates clamp force up to yield | n/a | n/a | traceable calibration required |
| Grade | Key Composition, % |
|---|---|
| Various | Base fastener made from any material/grade defined by a governing engineering standard; F2482 adds load-indication and traceability requirements |
Applies over base specs such as A325/A490/F3125, A193, F2281; related to F2437/F959 (washer-type indicators)
For the official ASTM International standards catalogue, see the ASTM International standards listing. This external reference is provided for standards identification; the purchaser should verify the current edition applicable to the order.
We supply ASTM F2482/F2482M fasteners — bolts, screws, studs, nuts and washers as applicable — for energy, petrochemical, marine, structural and general engineering service, in a full range of sizes and finishes.
For technical documentation and quotations, buyers can also review the Ananka Fasteners manufacturing and supply range or contact the team through the fastener enquiry and technical support page.
Ananka Fasteners supplies every lot with full material traceability and third-party testing on request.
CORRECTION: ASTM F2482 is ‘Load-Indicating Externally Threaded Fasteners’ – bolts, studs and cap screws with integral sensing that indicate clamp force during tightening or residual tension in service (not a generic bolt material spec). Sizes 1/4 to 7 in [M6-M180].
Ananka Fasteners supplies Mechanical Dial Type (MT), Electronic Type (ET), Strain Gauge Type (ST), Ultrasonic Type (UT) to ASTM F2482/F2482M. See the Grades / Classes Covered table above for full details of each grade.
Minimum tensile strength, yield strength, elongation and hardness requirements vary by grade — see the Mechanical Properties table above for the complete breakdown.
We supply ASTM F2482/F2482M fasteners — bolts, screws, studs, nuts and washers as applicable — for energy, petrochemical, marine, structural and general engineering service, in a full range of sizes and finishes.
Yes. For a quotation, provide the required fastener type, grade, nominal size, dimensional standard, quantity and any inspection or certificate requirements.
Need a fastener released to ASTM F2482/F2482M for an industrial project? Send the required fastener type, grade, size, quantity and certification requirements to Ananka Fasteners. Our team can review the requirement and provide technical and commercial information for standard or custom configurations.
Recommended RFQ details: ASTM F2482/F2482M requirement, material grade, fastener type, nominal size, dimensional standard, quantity, inspection requirements and EN 10204 certificate requirements where applicable.
Data compiled per ASTM F2482/F2482M and industry references; provided for reference only — confirm against the current edition of the standard and certified mill test reports before design use.
