At Ananka Fasteners Pvt Ltd, we manufacture fasteners to the dimensional requirements of DIN 922. DIN 922 covers slotted pan head screws with a small head and a full dog point (an unthreaded cylindrical extension at the tip that acts as a locating/aligning pilot). It shares the small-head geometry of DIN 920 and adds the dog point. Values below combine the small-head dimensions with the dog-point length.
DIN 922 covers slotted pan head screws with a small head and a full dog point (an unthreaded cylindrical extension at the tip that acts as a locating/aligning pilot). It shares the small-head geometry of DIN 920 and adds the dog point. Values below combine the small-head dimensions with the dog-point length.
Slotted pan head screw, small head, with full dog point
Key dimensions for common sizes are listed below.
| Thread d | Head Dia dk (mm) | Head Height k (mm) | Slot Width n (mm) | Dog Point Length z (mm) |
|---|---|---|---|---|
| M2 | 3.5 | 1.1 | 0.5 | 1.0 |
| M2.5 | 4.5 | 1.4 | 0.6 | 1.25 |
| M3 | 5.0 | 1.6 | 0.8 | 1.5 |
| M4 | 6.0 | 2.0 | 1.0 | 2.0 |
| M5 | 7.0 | 2.5 | 1.2 | 2.5 |
| M6 | 8.5 | 3.0 | 1.6 | 3.0 |
| M8 | 11.0 | 4.0 | 2.0 | 4.0 |
ISO metric coarse thread, tolerance 6g per ISO 965
[‘DIN 920 (slotted pan, small head, no dog point)’, ‘DIN 921 (slotted pan, large head)’, ‘DIN 417 (slotted set screw, long dog point)’]
For the official DIN standards catalogue, see the DIN standards listing. This external reference is provided for standards identification; the purchaser should verify the current edition applicable to the order.
We produce DIN 922 fasteners in carbon and alloy steel, austenitic, duplex and super-duplex stainless, and high-nickel, titanium and copper alloys — for structural, flanged, machinery and process applications worldwide.
For technical documentation and quotations, buyers can also review the Ananka Fasteners manufacturing and supply range or contact the team through the fastener enquiry and technical support page.
Ananka Fasteners supplies every lot with full material traceability and third-party testing on request.
DIN 922 covers slotted pan head screws with a small head and a full dog point (an unthreaded cylindrical extension at the tip that acts as a locating/aligning pilot). It shares the small-head geometry of DIN 920 and adds the dog point. Values below combine the small-head dimensions with the dog-point length.
Ananka Fasteners manufactures DIN 922 in sizes from M2–M8. See the Dimensional Table above for the complete size breakdown.
ISO metric coarse thread, tolerance 6g per ISO 965
We produce DIN 922 fasteners in carbon and alloy steel, austenitic, duplex and super-duplex stainless, and high-nickel, titanium and copper alloys — for structural, flanged, machinery and process applications worldwide.
Yes. For a quotation, provide the required nominal size, material grade, quantity and any inspection or certificate requirements.
Need a fastener manufactured to DIN 922 for an industrial project? Send the required fastener type, size, material grade, quantity and certification requirements to Ananka Fasteners. Our team can review the requirement and provide technical and commercial information for standard or custom configurations.
Recommended RFQ details: DIN 922 requirement, nominal size, material grade, quantity, inspection requirements and EN 10204 certificate requirements where applicable.
Dimensions compiled per DIN 922 and industry references; provided for reference only — confirm against the current edition of the standard before design use.
