At Ananka Fasteners Pvt Ltd, we manufacture and supply fasteners certified to ASTM A1014/A1014M. ASTM A1014/A1014M covers precipitation-hardening nickel-based alloy bolting (UNS N07718, Alloy 718 / Inconel 718) for high-temperature and corrosive service, including bolts, studs, screws, and threaded rod. Material is age-hardened to develop high strength retained at elevated temperature, in inch sizes 1/4 in. to 4 in. and metric M6 to M100.
ASTM A1014/A1014M covers precipitation-hardening nickel-based alloy bolting (UNS N07718, Alloy 718 / Inconel 718) for high-temperature and corrosive service, including bolts, studs, screws, and threaded rod. Material is age-hardened to develop high strength retained at elevated temperature, in inch sizes 1/4 in. to 4 in. and metric M6 to M100.
| Grade / Class | UNS / Designation | Type / Notes |
|---|---|---|
| UNS N07718 | N07718 (Alloy 718) | Precipitation-hardening Ni-Cr-Fe alloy, solution treated and aged |
Minimum mechanical requirements per ASTM A1014/A1014M.
| Grade / Class / Condition | Tensile Strength, min | Yield Strength, min | Elongation, min % | Hardness |
|---|---|---|---|---|
| UNS N07718, aged | 185 (1275) min | 150 (1035) min | 12 | 331-444 HBW |
| Grade | Key Composition, % |
|---|---|
| UNS N07718 | Ni 50-55, Cr 17-21, Fe balance, Nb+Ta 4.75-5.5, Mo 2.8-3.3, Ti 0.65-1.15, Al 0.2-0.8, C 0.08 max |
Uses bar stock per ASTM B637 (UNS N07718). Comparable to AMS 5662/5663 for Alloy 718 and to API 6A/6ACRA nickel-alloy bolting requirements for oil-and-gas service.
For the official ASTM International standards catalogue, see the ASTM International standards listing. This external reference is provided for standards identification; the purchaser should verify the current edition applicable to the order.
We supply ASTM A1014/A1014M fasteners — bolts, screws, studs, nuts and washers as applicable — for energy, petrochemical, marine, structural and general engineering service, in a full range of sizes and finishes.
For technical documentation and quotations, buyers can also review the Ananka Fasteners manufacturing and supply range or contact the team through the fastener enquiry and technical support page.
Ananka Fasteners supplies every lot with full material traceability and third-party testing on request.
ASTM A1014/A1014M covers precipitation-hardening nickel-based alloy bolting (UNS N07718, Alloy 718 / Inconel 718) for high-temperature and corrosive service, including bolts, studs, screws, and threaded rod. Material is age-hardened to develop high strength retained at elevated temperature, in inch sizes 1/4 in. to 4 in. and metric M6 to M100.
Ananka Fasteners supplies UNS N07718 to ASTM A1014/A1014M. See the Grades / Classes Covered table above for full details of each grade.
Minimum tensile strength, yield strength, elongation and hardness requirements vary by grade — see the Mechanical Properties table above for the complete breakdown.
We supply ASTM A1014/A1014M fasteners — bolts, screws, studs, nuts and washers as applicable — for energy, petrochemical, marine, structural and general engineering service, in a full range of sizes and finishes.
Yes. For a quotation, provide the required fastener type, grade, nominal size, dimensional standard, quantity and any inspection or certificate requirements.
Need a fastener released to ASTM A1014/A1014M for an industrial project? Send the required fastener type, grade, size, quantity and certification requirements to Ananka Fasteners. Our team can review the requirement and provide technical and commercial information for standard or custom configurations.
Recommended RFQ details: ASTM A1014/A1014M requirement, material grade, fastener type, nominal size, dimensional standard, quantity, inspection requirements and EN 10204 certificate requirements where applicable.
Data compiled per ASTM A1014/A1014M and industry references; provided for reference only — confirm against the current edition of the standard and certified mill test reports before design use.
