At Ananka Fasteners Pvt Ltd, we manufacture and supply fasteners certified to ASTM B162. Nickel plate, sheet and strip (Nickel 200 UNS N02200 and low-carbon Nickel 201 UNS N02201). Commercially pure nickel plate feeding stamped washers, gaskets and backing plates for caustic and chemical service. Values ksi with (MPa).
Nickel plate, sheet and strip (Nickel 200 UNS N02200 and low-carbon Nickel 201 UNS N02201). Commercially pure nickel plate feeding stamped washers, gaskets and backing plates for caustic and chemical service. Values ksi with (MPa).
| Grade / Class | UNS / Designation | Type / Notes |
|---|---|---|
| Nickel 200 | N02200 | 99% Ni, standard carbon |
| Nickel 201 | N02201 | 99% Ni, low carbon (0.02 max) |
Minimum mechanical requirements per ASTM B162.
| Grade / Class / Condition | Tensile Strength, min | Yield Strength, min | Elongation, min % | Hardness |
|---|---|---|---|---|
| N02200 annealed (plate/sheet) | 55 (380) | 15 (100) | 40 | – |
| N02200 as-rolled plate | 55 (380) | 20 (135) | 30 | – |
| N02200 hard sheet/strip | 90 (620) | 70 (480) | 2 | – |
| N02201 annealed (plate/sheet) | 50 (345) | 12 (80) | 40 | – |
| N02201 as-rolled plate | 50 (345) | 12 (80) | 30 | – |
| Grade | Key Composition, % |
|---|---|
| N02200 | Ni 99.0 min, C 0.15 max, Fe 0.40 max, Mn 0.35 max, Cu 0.25 max, Si 0.35 max, S 0.01 max |
| N02201 | Ni 99.0 min, C 0.02 max, Fe 0.40 max, Mn 0.35 max, Cu 0.25 max |
UNS N02200/N02201; ASME SB162; rod equivalent ASTM B160; Nickel 200 = 2.4066
For the official ASTM International standards catalogue, see the ASTM International standards listing. This external reference is provided for standards identification; the purchaser should verify the current edition applicable to the order.
We supply ASTM B162 fasteners — bolts, screws, studs, nuts and washers as applicable — for energy, petrochemical, marine, structural and general engineering service, in a full range of sizes and finishes.
For technical documentation and quotations, buyers can also review the Ananka Fasteners manufacturing and supply range or contact the team through the fastener enquiry and technical support page.
Ananka Fasteners supplies every lot with full material traceability and third-party testing on request.
Nickel plate, sheet and strip (Nickel 200 UNS N02200 and low-carbon Nickel 201 UNS N02201). Commercially pure nickel plate feeding stamped washers, gaskets and backing plates for caustic and chemical service. Values ksi with (MPa).
Ananka Fasteners supplies Nickel 200, Nickel 201 to ASTM B162. See the Grades / Classes Covered table above for full details of each grade.
Minimum tensile strength, yield strength, elongation and hardness requirements vary by grade — see the Mechanical Properties table above for the complete breakdown.
We supply ASTM B162 fasteners — bolts, screws, studs, nuts and washers as applicable — for energy, petrochemical, marine, structural and general engineering service, in a full range of sizes and finishes.
Yes. For a quotation, provide the required fastener type, grade, nominal size, dimensional standard, quantity and any inspection or certificate requirements.
Need a fastener released to ASTM B162 for an industrial project? Send the required fastener type, grade, size, quantity and certification requirements to Ananka Fasteners. Our team can review the requirement and provide technical and commercial information for standard or custom configurations.
Recommended RFQ details: ASTM B162 requirement, material grade, fastener type, nominal size, dimensional standard, quantity, inspection requirements and EN 10204 certificate requirements where applicable.
Data compiled per ASTM B162 and industry references; provided for reference only — confirm against the current edition of the standard and certified mill test reports before design use.
